Hey friends,
I am thinking of a compressor setup in the car with additional small tank & some hose setup, if any one can help where to do this please. Further more I have new bushranger compressor wants to use it for the same.
Compressor fitting with a small tank
- Abdul Qadir
- Marshal
- Posts: 2944
- Joined: Mon Mar 26, 2012 7:40 pm
- Location: Abu Dhabi
- Location: MBZ Abu Dhabi
- Contact:
Compressor fitting with a small tank
0501212499
The way we see the problem is the problem.
The way we see the problem is the problem.
- DesertDawg
- Overseas Marshal
- Posts: 1302
- Joined: Mon Feb 21, 2011 10:13 pm
- Location: Abu Dhabi
Re: Compressor fitting with a small tank
This was my solution based on a ARB portable compressor:
http://compare.ebay.co.uk/like/25109154 ... pla&crdt=0
I cut the cable at about six inches from box and then used these connectors.
http://www.ebay.co.uk/itm/10-X-ANDERSON ... 20cead1f65
I the put connectors on the compressor / car wiring feed / crocodile leads.
This gives me the option to use the compressor in portable mode or wired in mode. The compressor is secured to the floor behind the driver's seat.
Cable:
My ARB draws 23 amps under load. I have used 4 meters 4.5mm2 cable which give a volt drop off 0.75v. That is if the battery is at 12V then with the compressor drawing 23 amp, I have 11.25 volts at the compressor.
I have used a 40A fuse (near the battery as possible) and a good quality 40A relay.
Here is the cct:
As to having a tank - is it really worth it? Unless it is HUGE it will be done for after the first tire. Time to move from one tire to the next won't be enough to have topped up tank to any useful degree.
Hope this helps.
Dave
http://compare.ebay.co.uk/like/25109154 ... pla&crdt=0
I cut the cable at about six inches from box and then used these connectors.
http://www.ebay.co.uk/itm/10-X-ANDERSON ... 20cead1f65
I the put connectors on the compressor / car wiring feed / crocodile leads.
This gives me the option to use the compressor in portable mode or wired in mode. The compressor is secured to the floor behind the driver's seat.
Cable:
My ARB draws 23 amps under load. I have used 4 meters 4.5mm2 cable which give a volt drop off 0.75v. That is if the battery is at 12V then with the compressor drawing 23 amp, I have 11.25 volts at the compressor.
I have used a 40A fuse (near the battery as possible) and a good quality 40A relay.
Here is the cct:
As to having a tank - is it really worth it? Unless it is HUGE it will be done for after the first tire. Time to move from one tire to the next won't be enough to have topped up tank to any useful degree.
Hope this helps.
Dave
You do not have the required permissions to view the files attached to this post.
Travelling in my truck...
- Abdul Qadir
- Marshal
- Posts: 2944
- Joined: Mon Mar 26, 2012 7:40 pm
- Location: Abu Dhabi
- Location: MBZ Abu Dhabi
- Contact:
Re: Compressor fitting with a small tank
Thanks a lot Dave
0501212499
The way we see the problem is the problem.
The way we see the problem is the problem.
- ossme
- Marshal
- Posts: 2039
- Joined: Sat May 21, 2011 11:32 am
- Location: Abu Dhabi
Re: Compressor fitting with a small tank
A tank is so small that makes it useless. It is better to use a high output air compressor.
Proud to be Ad4x4 Marshal. ![Smile :)](./images/smilies/icon_e_smile.gif)
![Smile :)](./images/smilies/icon_e_smile.gif)